China Belt Conveyor Pulley for Mining and Mineral Application idler pulley

Merchandise Description

We can produce conveyor rollers of different standards, diameters, lengths, and sorts
Welcome to compose to us
Ā 

Item Description

Ā 

Description Fabrication Solutions flat belt idler pulley for belt conveyor
Application Employed in electrical electricity, metallurgy,mine,coal, cement,steel,chemical, port, hydroelectric energy and CZPT industries
Pipe/Tube/Shell one)Content:Q235 Steel
2)Diameter:219mm-3000mm
three)Length:500mm-5000mm,depends on the belt width of the conveyor
Shaft/Axis Materials:#forty five Steel
Bearing Big roving crack, deep groove ball with double sealing
Welding Pipe and bearing housing with computerized welding
Surface Sleek metal colour surface,Ā Ā rubber lagging surface
Color Red,inexperienced,blue or as call for
Provider life A lot more than thirty,000 hrs
Standard GB,ISO,DIN,CEMA,JIS

Our Pulley Characteristics:
Ā 

Conveyor PulleyĀ Ā Test Ā 
1. All butt welds shall be entire Penetration
2. All welds to be complete seal welds to stop rust
3. Shell seam welds are submerged arc (Observed)
4. Involves stress relieving of shell prior to machining
five. Ultrasonic screening of all shafts
six. Drillings for Temperature probe /Ā vibration analysis system
seven. Remove all butts and sharp edges
Conveyor Pulley Shaft Variety Ā 
The major lead to of conveyor pulley failure is abnormal shaft deflection. The Conveyor Pulleys –Ā ZheJiang HSCD Engineering office can complete Stress Investigation and Finite Component Examination to maximize your conveyor pulley overall performance.Ā 
Ā 
Conveyor Pulley Shell Materials Ā 
Q345B Carbon Steel
GR350 Carbon Metal
ANSI 4140 Alloy Steel
ASTM A514B Stainless Metal
Bearing HouseĀ  Ā SKF/NSK/ /HRB/LYC, as consumer ask for.Ā 
Conveyor Pulley Lagging Ā 
Basic rubber lagging, Herringbone and CZPT grooves are all availableĀ 
. Sizzling Vulcanised DurometerĀ 
. Hardness fifty-fifty five-65 Shore A, MĀ Grade
. Oil Resistant, Heat Resistant FRAS
Comprising Ā 
ā€¢Drive pulley, Head pulley and Tail Pulleys
ā€¢Take-Up Pulleys,
ā€¢Snub pulley &Ā Bend Pulleys
ā€¢Self Cleansing Spiral CZPT pulley &Ā Drum Pulleys
Considerable advantages Ā 
ā€¢ The thick pulley shell absorbs much more stress.
ā€¢ The big crown angle offers exceptional belt tracking capabilities.
ā€¢ Accurate concentric machining supplies:
ā€¢ optimum make contact with with the belt,
ā€¢ regular belt content material discharge,
ā€¢ significantly less deflection of shaft,
ā€¢ less anxiety on the bearings
Available
Conveyor Pulley Types
Ā 
ā€¢Liveshaft or Deadshaft types.
ā€¢Flat or topped shell.
ā€¢Taconite, labyrinth or speciality seals.
ā€¢Oil or grease lubricated.
ā€¢Self centering or lower pressure lock factor designs.

Ā 

Our workshop

Our packaging

our items

Our certificate

Ā 

Our make contact with

Ā 

Ā 

Ā 

Ā 

US $300
/ Piece
|
1,000 Pieces

(Min. Order)

###

Material: Carbon Steel
Surface Treatment: Polishing
Motor Type: Frequency Control Motor
Installation: Turning
Thickness of Rubber Surface: 8mm 10mm 12mm 15mm 20mm
Diameter: 159—2000mm

###

Customization:

###

Description Fabrication Services flat belt idler pulley for belt conveyor
Application Used in electric power, metallurgy,mine,coal, cement,steel,chemical, port, hydroelectric power and grain industries
Pipe/Tube/Shell 1)Material:Q235 Steel
2)Diameter:219mm-3000mm
3)Length:500mm-5000mm,depends on the belt width of the conveyor
Shaft/Axis Material:#45 Steel
Bearing Big roving crack, deep groove ball with double sealing
Welding Pipe and bearing housing with automatic welding
Surface Smooth steel color surface,  rubber lagging surface
Color Red,green,blue or as require
Service life More than 30,000 hours
Standard GB,ISO,DIN,CEMA,JIS

###

Conveyor Pulley  Test  
1. All butt welds shall be full Penetration
2. All welds to be full seal welds to prevent rust
3. Shell seam welds are submerged arc (SAW)
4. Includes stress relieving of shell prior to machining
5. Ultrasonic testing of all shafts
6. Drillings for Temperature probe / vibration analysis device
7. Remove all butts and sharp edges
Conveyor Pulley Shaft Selection  
The major cause of conveyor pulley failure is excessive shaft deflection. The Conveyor Pulleys – Beijing HSCD Engineering department can perform Stress Analysis and Finite Element Analysis to maximize your conveyor pulley performance. 
 
Conveyor Pulley Shell Material  
Q345B Carbon Steel
GR350 Carbon Steel
ANSI 4140 Alloy Steel
ASTM A514B Stainless Steel
Bearing House   SKF/NSK/ /HRB/LYC, as customer request. 
Conveyor Pulley Lagging  
Plain rubber lagging, Herringbone and Diamond grooves are all available 
. Hot Vulcanised Durometer 
. Hardness 50-55-65 Shore A, M Grade
. Oil Resistant, Heat Resistant FRAS
Comprising  
•Drive pulley, Head pulley and Tail Pulleys
•Take-Up Pulleys,
•Snub pulley & Bend Pulleys
•Self Cleaning Spiral Wing pulley & Drum Pulleys
Significant advantages  
• The thick pulley shell absorbs more stress.
• The large crown angle provides superior belt tracking capabilities.
• True concentric machining provides:
• maximum contact with the belt,
• consistent belt content discharge,
• less deflection of shaft,
• less stress on the bearings
Available
Conveyor Pulley Designs
 
•Liveshaft or Deadshaft types.
•Flat or crowned shell.
•Taconite, labyrinth or speciality seals.
•Oil or grease lubricated.
•Self centering or low pressure lock element designs.
US $300
/ Piece
|
1,000 Pieces

(Min. Order)

###

Material: Carbon Steel
Surface Treatment: Polishing
Motor Type: Frequency Control Motor
Installation: Turning
Thickness of Rubber Surface: 8mm 10mm 12mm 15mm 20mm
Diameter: 159—2000mm

###

Customization:

###

Description Fabrication Services flat belt idler pulley for belt conveyor
Application Used in electric power, metallurgy,mine,coal, cement,steel,chemical, port, hydroelectric power and grain industries
Pipe/Tube/Shell 1)Material:Q235 Steel
2)Diameter:219mm-3000mm
3)Length:500mm-5000mm,depends on the belt width of the conveyor
Shaft/Axis Material:#45 Steel
Bearing Big roving crack, deep groove ball with double sealing
Welding Pipe and bearing housing with automatic welding
Surface Smooth steel color surface,  rubber lagging surface
Color Red,green,blue or as require
Service life More than 30,000 hours
Standard GB,ISO,DIN,CEMA,JIS

###

Conveyor Pulley  Test  
1. All butt welds shall be full Penetration
2. All welds to be full seal welds to prevent rust
3. Shell seam welds are submerged arc (SAW)
4. Includes stress relieving of shell prior to machining
5. Ultrasonic testing of all shafts
6. Drillings for Temperature probe / vibration analysis device
7. Remove all butts and sharp edges
Conveyor Pulley Shaft Selection  
The major cause of conveyor pulley failure is excessive shaft deflection. The Conveyor Pulleys – Beijing HSCD Engineering department can perform Stress Analysis and Finite Element Analysis to maximize your conveyor pulley performance. 
 
Conveyor Pulley Shell Material  
Q345B Carbon Steel
GR350 Carbon Steel
ANSI 4140 Alloy Steel
ASTM A514B Stainless Steel
Bearing House   SKF/NSK/ /HRB/LYC, as customer request. 
Conveyor Pulley Lagging  
Plain rubber lagging, Herringbone and Diamond grooves are all available 
. Hot Vulcanised Durometer 
. Hardness 50-55-65 Shore A, M Grade
. Oil Resistant, Heat Resistant FRAS
Comprising  
•Drive pulley, Head pulley and Tail Pulleys
•Take-Up Pulleys,
•Snub pulley & Bend Pulleys
•Self Cleaning Spiral Wing pulley & Drum Pulleys
Significant advantages  
• The thick pulley shell absorbs more stress.
• The large crown angle provides superior belt tracking capabilities.
• True concentric machining provides:
• maximum contact with the belt,
• consistent belt content discharge,
• less deflection of shaft,
• less stress on the bearings
Available
Conveyor Pulley Designs
 
•Liveshaft or Deadshaft types.
•Flat or crowned shell.
•Taconite, labyrinth or speciality seals.
•Oil or grease lubricated.
•Self centering or low pressure lock element designs.

How to Assemble a Pulley System

A pulley is a wheel that rotates on a shaft or shaft to support the movement of a taut cable. Pulleys allow power to be transmitted from the shaft to the cable.
pulley

Simple pulley

The simplest theory of operation of a pulley system assumes that the rope and weight are weightless and that the rope and pulley are not stretched. Since the force on the pulley is the same, the force on the pulley shaft must also be zero. Therefore, the force exerted on the pulley shaft is also distributed evenly between the two wires passing through the pulley. The force distribution is shown in Figure 1.
The use of simple pulleys is as old as history. Before the Industrial Revolution, people relied on muscle strength to carry heavy loads. Pulleys, levers and ramps make this possible. Today, we can see pulleys in a variety of systems, from exercise equipment to garage doors, and even rock climbers use them to help them reach greater heights. As you can see, these simple machines have been around for centuries and are used in everyday life.
Another simple pulley system is the pulley system. In this system, there is a fixed pulley at the top and a movable pulley at the bottom. The two pulleys are connected by a rope. This combination reduces the amount of work required to lift the load. Additionally, the ropes used in this system are usually made of rope and woven through the individual wheels of the pulley drum.
A pulley is an ingenious device that distributes weight evenly and can be used to lift heavy objects. It is easy to build and can be easily modified for a wide range of activities. Even young children can make their own with very few materials. You can also use simple household items such as washing machines, thin textbooks and even chopsticks. It’s very useful and can be a great addition to your child’s science and engineering activities.
The simplest pulley system is movable. The axis of the movable pulley can move freely in space. The load is attached to one end of the pulley and the other end to the stationary object. By applying force on the other end of the rope, the load is lifted. The force at the other end of the rope is equal to the force at the free end of the pulley.
Another form of pulley is the compound pulley. Compound pulleys use two or more wheels to transmit force. Compound pulleys have two or more wheels and can lift heavier objects. Dim is POLE2.
pulley

tapered pulley

It is important to clean and align the bolt holes before assembling the tapered pulley. The screws should be lubricated and the threads cleaned before installation. To install the pulley, insert it into the shaft keyway. The keyway should be aligned with the shaft hole to prevent foreign matter from entering the pulley. Then, alternately tighten the bolts until the pulley is tightened to the desired torque.
A tapered pulley is a basic structure. The pulley belt is arranged across four steps. Installed between the headstock casting and the main shaft, it is often used in the paper industry. It integrates with printing machinery and supports assembly lines. These pulleys are also available in metric range options, eliminating the need for ke-waying or re-drilling. They are easy to install, and users can even customize them to suit their needs.
CZPT Private Limited is a company that provides unique products for various industries. This large product is used for many different purposes. Also, it is manufactured for industrial use. The company’s website provides detailed specifications for the product. If you need a tapered pulley, contact a company in your area today to purchase a quality product!
Tapered pulleys are vital to paper mill machinery. Its special design and construction enable it to transmit power from the engine source to the drive components. The advantages of this pulley include low maintenance costs and high mechanical strength. Cone wheel diameters range from 10 inches to 74 inches. These pulleys are commonly used in paper mills as they offer low maintenance, high mechanical strength and low wear.
A tapered sleeve connects the pulley to the shaft and forms an interference fit connector. The taper sleeve is fixed on the shaft with a key, and the corresponding inner hole is fixed on the shaft with a key. These features transmit torque and force to the pulley through friction. This allows the tapered pulley to move in a circular motion. The torque transfer characteristics of this pulley are most effective in high speed applications.
The sleeve is the most important part when assembling the tapered pulley. There is an 8-degree taper inside the cone, which is closely connected to the inner surface of the pulley. Taper sleeves and pulleys are interchangeable. However, tapered pulleys can be damaged after prolonged use.
pulley

pulley pulley system

A pulley pulley system is a great way to move heavy objects. These systems have been around for centuries, dating back to the ancient Greeks. This simple mechanism enables a person to lift heavy objects. These blocks are usually made of rope, and the number of turns varies for different types of rope. Some blocks have more cords than others, which creates friction and interferes with the easy movement of the lifting system.
When using a pulley pulley, the first thing to decide is which direction to pull. Unfavorable rigging means pulling in the opposite direction. In theory, this method is less efficient, but sometimes requires a certain amount of work space. The benefit is that you will increase the mechanical advantage of the pulley by pulling in the opposite direction. So the interception and tackle system will give you more of a mechanical advantage.
Pulley pulleys are an excellent choice for lifting heavy objects. The system is simple to install and users can easily lift objects without extensive training. Figure 3.40 shows a pulley in action. In this photo, the person on the left is pulling a rope and tying the end of the rope to a weight. When the rope is attached to the load, the rope will be pulled over the pulley and pulley.
The blocks on the blocks are attached to the ends of the rope. This creates unique lifting advantages compared to single-line systems. In Figure 3, the tension of each thread is equal to one-third of the unit weight. When the rope is pulled over the pulley, the force is divided equally between the two wires. The other pulley reverses the direction of the force, but that doesn’t add any advantage.
Use pulleys to reduce traction and load. The weight of the load has not changed, but the length of the rope has increased. Using this method, lifting the load by pulling the rope four times reduces the force required to lift one foot. Likewise, if the pulley system had four pulleys instead of three, the length of the rope would be tripled.
The system can transmit loads in any direction. Rope length is determined by multiplying the distance from the fixed block to the load by the mechanical advantage. If the mechanical advantage is 3:1, then passing the rope through the pulley 3 times will produce the required traction distance. Also, the length of the rope will depend on the mechanical advantage, so if the load is three times the length of the rope, it will be more than three times the required length.

China Belt Conveyor Pulley for Mining and Mineral Application     idler pulley	China Belt Conveyor Pulley for Mining and Mineral Application     idler pulley
editor by czh 2022-11-30

Drive Belt Pulley

As one of the drive belt pulley manufacturers, suppliers, and exporters of mechanical products, We offer drive belt pulley and many other products.

Please get in touch with us for details.

Manufacturer supplier exporter of the drive belt pulley.